Post Reply 
 
Thread Rating:
  • 1 Votes - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Kernel panic - not syncing: No init found.
08-19-2015, 03:39 PM
Post: #1
Kernel panic - not syncing: No init found.
I recently updated my DroboFS to the newest firmware. It was working afterwords, but now won't boot.

I've attached a serial adapter to the Linux CPU, and it looks like filesystem has been corrupted. Is there any way to recover from this?

Code:
__  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
_   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/    |____/ \___/ \___/ \__|  ** LOADER **
** MARVELL BOARD: DB-MV78200-A-BP LE

U-Boot 1.1.4 (Jan 20 2011 - 14:23:47) Marvell version: 3.3.5 - (DroboNAS Dual CPU) DRI version: 0.55

U-Boot code: 00F10000 -> 00F8FFF0  BSS: -> 00FEC0E0

Soc: MV78200 (DDR2)
CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  64bit width
Flash: 128 MB
Addresses 18M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (18M - 17M): Done

CPU 1: ARM926 (Rev 0)

Streaming enabled
Write allocate enabled
FPU initialized to Run Fast Mode.


Net:   eth_register: cur:egiga1 act:egiga0
egiga1 [PRIME]
Hit any key to stop autoboot:  0
Booting from flash....
Check image #1 ... OK.
  version = 43.62623.0, imageAddress = 0xf8100000, imageLength = 0x1b2f9a4 bootFailureCount = 0, sequenceNum = 6
Check image #2 ... OK.
  version = 44.64324.0, imageAddress = 0xf9dc0000, imageLength = 0x1b2f9cf bootFailureCount = 1, sequenceNum = 7
Selecting image #2
Copying header from flash to ram: src: 0xf8040000, dst: 0xfb000c size: 556
td_bootImage: loadaddrStr: 0xf9dc0000, in: 0xfb000c, ntohl(ih->imageFlashAddress): 0xf9dc0000, 0xdcf9, ntohl(ih->segments[i].segmentOffset): 0x0, 0x0
## Booting image at f9dc0000 ...
   Image Name:   Linux-2.6.22.18
   Created:      2013-05-22  23:43:06 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1599208 Bytes =  1.5 MB
   Load Address: 08008000
   Entry Point:  08008000
   Verifying Checksum ... OK
OK
bootargs: console=ttyS0,115200 mtdparts=cfi_flash_0:3m@30464k(kernel),21m@33536k(root_fs),2m@59m(var) root=/dev/mtdblock1 rw cpu0=eth0,eth2,eth3,pcie0,pcie1,sata,nand,spi,usb0,usb1,usb2,tdm cpu1=eth1,nor,xor ip=169.254.1.0:169.254.123.234:::DB78xx0:eth0:none

Starting kernel ...

Uncompressing Linux........................................................................................................ done, booting the kernel.
Linux version 2.6.22.18 (root@jwinfield01) (gcc version 4.2.0 20070413 (prerelease)) #1 Wed May 22 16:43:02 PDT 2013
CPU: ARM926EJ-S [41159260] revision 0 (ARMv5TE), cr=00053977
Machine: Feroceon-MV78XX0
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
free_area_init_core: realsize: 48128, size: 131072, memmap_pages: 1024
free_area_init_core: realsize: 0, size: 0, memmap_pages: 0
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists.  Total pages: 48128
Kernel command line: console=ttyS0,115200 mtdparts=cfi_flash_0:3m@30464k(kernel),21m@33536k(root_fs),2m@59m(var) root=/dev/mtdblock1 rw cpu0=eth0,eth2,eth3,pcie0,pcie1,sata,nand,spi,usb0,usb1,usb2,tdm cpu1=eth1,nor,xor ip=169.254.1.0:169.254.123.234:::DB78xx0:eth0:none
IRQ initialize for core 1
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 512MB 0MB 0MB 0MB = 512MB total
Memory: 188800KB available (2984K code, 255K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

CPU 1, CPU Interface
-------------
SDRAM_CS0.... ....base 00000000, size 512MB
SDRAM_CS1.... ....disable
SDRAM_CS2.... ....disable
SDRAM_CS3.... ....disable
DEVICE_CS0... ....no such
DEVICE_CS1... ....base fe000000, size   1MB
DEVICE_CS2... ....no such
DEVICE_CS3... ....base fd000000, size   1MB
DEV_BOOCS.... ....base f8000000, size  64MB
DEVICE_SPI... ....no such
PEX0_IO...... ....base f2000000, size   8MB
PEX0_MEM0.... ....base c8000000, size  64MB
PEX1_IO...... ....base f3000000, size   8MB
PEX1_MEM0.... ....base cc000000, size  64MB
PEX2_IO...... ....no such
PEX2_MEM0.... ....no such
PEX3_IO...... ....base f5000000, size   8MB
PEX3_MEM0.... ....base d4000000, size  64MB
PEX4_IO...... ....base f6000000, size   8MB
PEX4_MEM0.... ....base d8000000, size  64MB
PEX5_IO...... ....no such
PEX5_MEM0.... ....no such
PEX6_IO...... ....no such
PEX6_MEM0.... ....no such
PEX7_IO...... ....no such
PEX7_MEM0.... ....no such
CRYPT_ENG..... ....base f7000000, size   2MB
INTER_REGS... ....base f1000000, size   1MB

  Marvell Development Board (LSP Version 2.0.2_Patch1_MV78XX0)-- DB-MV78200-A-BP  Soc: MV78200 LE

Detected Tclk 200000000 and SysClk 400000000
pci_preinit(): PCI-E 0 not mapped to this CPU.
pci_preinit(): PCI-E 1 not mapped to this CPU.
pci_preinit(): PCI-E 2 not mapped to this CPU.
pci_preinit(): PCI-E 3 not mapped to this CPU.
pci_preinit(): PCI-E 4 not mapped to this CPU.
pci_preinit(): PCI-E 5 not mapped to this CPU.
pci_preinit(): PCI-E 6 not mapped to this CPU.
pci_preinit(): PCI-E 7 not mapped to this CPU.
mv_pci_setup(): PCI-E 0 not mapped to this CPU.
mv_pci_setup(): PCI-E 1 not mapped to this CPU.
mv_pci_setup(): PCI-E 2 not mapped to this CPU.
mv_pci_setup(): PCI-E 3 not mapped to this CPU.
mv_pci_setup(): PCI-E 4 not mapped to this CPU.
mv_pci_setup(): PCI-E 5 not mapped to this CPU.
mv_pci_setup(): PCI-E 6 not mapped to this CPU.
mv_pci_setup(): PCI-E 7 not mapped to this CPU.
SCSI subsystem initialized
NET: Registered protocol family 2
Time: orion_clocksource clocksource has been installed.
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
RTC registered.
SHARED_MEM: INIT: Shared Memory mapped into Kernel space at Addr: 0x0 for size 0xc000000
SHARED_MEM: INIT: Shared Memory Header in Kernel space at Addr: 0xa0800000
shared_mem_module_init: Location of shm_dev: 93c14000
Use the XOR engines (acceleration) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
  o copy user to/from kernel buffers
Number of XOR engines to use: 1
Use IDMA channels for enhancing the following function:
Enable iDMA idma_chan0 interrupt IRQ 4 for iDMA 0
Enable iDMA idma_chan1 interrupt IRQ 5 for iDMA 1
Enable iDMA idma_chan2 interrupt IRQ 6 for iDMA 2
Enable iDMA idma_chan3 interrupt IRQ 7 for iDMA 3
mv_dma_init: iDMA channel 1 settings, state 0x00000000, cause 0x00000000 [0x00000000], mask 0x000004f0 [0x00000000], idmaCause 0x00000000, idmaMask 0x00000018
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 13) is a 16550A
Load Marvell Ethernet Driver
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload enabled
  o Receive checksum offload enabled
  o Transmit checksum offload enabled
  o Driver statistics enabled
  o Proc tool API enabled
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface:
Giga 0 is not mapped to this CPU
eth0 Giga 2 is not mapped to this CPU
Giga 3 is not mapped to this CPU

wait_for_init_shared_mem: Entering Mutex for shared memory init
SHARED_MEM: CPU1: READY TO WAIT FOR INITIALIZATION OF SHARED MEMORY
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
cfi_flash_0: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
cfi_flash_0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
3 cmdlinepart partitions found on MTD device cfi_flash_0
Creating 3 MTD partitions on "cfi_flash_0":
0x01dc0000-0x020c0000 : "kernel"
0x020c0000-0x035c0000 : "root_fs"
0x03b00000-0x03d00000 : "var"
mice: PS/2 mouse device common for all mice
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
eth0: started
IP-Config: Guessing netmask 255.255.0.0
IP-Config: Complete:
      device=eth0, addr=169.254.1.0, mask=255.255.0.0, gw=255.255.255.255,
     host=DB78xx0, domain=, nis-domain=(none),
     bootserver=169.254.123.234, rootserver=169.254.123.234, rootpath=
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 108K
Warning: unable to open an initial console.
Kernel panic - not syncing: No init found.  Try passing init= option to kernel.
shared_mem_panic_event: Kernel panic event handler called. Notifying VxWorks Core of Kernel panic.
Find all posts by this user
Quote this message in a reply
08-19-2015, 04:17 PM
Post: #2
RE: Kernel panic - not syncing: No init found.
Would you create a support case via our online support portal and then message me the case number.

https://myproducts.drobo.com/support

Thank You.
DroboMod


(08-19-2015 03:39 PM)nobodypanic Wrote:  I recently updated my DroboFS to the newest firmware. It was working afterwords, but now won't boot.

I've attached a serial adapter to the Linux CPU, and it looks like filesystem has been corrupted. Is there any way to recover from this?

Code:
__  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
_   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/    |____/ \___/ \___/ \__|  ** LOADER **
** MARVELL BOARD: DB-MV78200-A-BP LE

U-Boot 1.1.4 (Jan 20 2011 - 14:23:47) Marvell version: 3.3.5 - (DroboNAS Dual CPU) DRI version: 0.55

U-Boot code: 00F10000 -> 00F8FFF0  BSS: -> 00FEC0E0

Soc: MV78200 (DDR2)
CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  64bit width
Flash: 128 MB
Addresses 18M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (18M - 17M): Done

CPU 1: ARM926 (Rev 0)

Streaming enabled
Write allocate enabled
FPU initialized to Run Fast Mode.


Net:   eth_register: cur:egiga1 act:egiga0
egiga1 [PRIME]
Hit any key to stop autoboot:  0
Booting from flash....
Check image #1 ... OK.
  version = 43.62623.0, imageAddress = 0xf8100000, imageLength = 0x1b2f9a4 bootFailureCount = 0, sequenceNum = 6
Check image #2 ... OK.
  version = 44.64324.0, imageAddress = 0xf9dc0000, imageLength = 0x1b2f9cf bootFailureCount = 1, sequenceNum = 7
Selecting image #2
Copying header from flash to ram: src: 0xf8040000, dst: 0xfb000c size: 556
td_bootImage: loadaddrStr: 0xf9dc0000, in: 0xfb000c, ntohl(ih->imageFlashAddress): 0xf9dc0000, 0xdcf9, ntohl(ih->segments[i].segmentOffset): 0x0, 0x0
## Booting image at f9dc0000 ...
   Image Name:   Linux-2.6.22.18
   Created:      2013-05-22  23:43:06 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1599208 Bytes =  1.5 MB
   Load Address: 08008000
   Entry Point:  08008000
   Verifying Checksum ... OK
OK
bootargs: console=ttyS0,115200 mtdparts=cfi_flash_0:3m@30464k(kernel),21m@33536k(root_fs),2m@59m(var) root=/dev/mtdblock1 rw cpu0=eth0,eth2,eth3,pcie0,pcie1,sata,nand,spi,usb0,usb1,usb2,tdm cpu1=eth1,nor,xor ip=169.254.1.0:169.254.123.234:::DB78xx0:eth0:none

Starting kernel ...

Uncompressing Linux........................................................................................................ done, booting the kernel.
Linux version 2.6.22.18 (root@jwinfield01) (gcc version 4.2.0 20070413 (prerelease)) #1 Wed May 22 16:43:02 PDT 2013
CPU: ARM926EJ-S [41159260] revision 0 (ARMv5TE), cr=00053977
Machine: Feroceon-MV78XX0
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
free_area_init_core: realsize: 48128, size: 131072, memmap_pages: 1024
free_area_init_core: realsize: 0, size: 0, memmap_pages: 0
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists.  Total pages: 48128
Kernel command line: console=ttyS0,115200 mtdparts=cfi_flash_0:3m@30464k(kernel),21m@33536k(root_fs),2m@59m(var) root=/dev/mtdblock1 rw cpu0=eth0,eth2,eth3,pcie0,pcie1,sata,nand,spi,usb0,usb1,usb2,tdm cpu1=eth1,nor,xor ip=169.254.1.0:169.254.123.234:::DB78xx0:eth0:none
IRQ initialize for core 1
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 512MB 0MB 0MB 0MB = 512MB total
Memory: 188800KB available (2984K code, 255K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

CPU 1, CPU Interface
-------------
SDRAM_CS0.... ....base 00000000, size 512MB
SDRAM_CS1.... ....disable
SDRAM_CS2.... ....disable
SDRAM_CS3.... ....disable
DEVICE_CS0... ....no such
DEVICE_CS1... ....base fe000000, size   1MB
DEVICE_CS2... ....no such
DEVICE_CS3... ....base fd000000, size   1MB
DEV_BOOCS.... ....base f8000000, size  64MB
DEVICE_SPI... ....no such
PEX0_IO...... ....base f2000000, size   8MB
PEX0_MEM0.... ....base c8000000, size  64MB
PEX1_IO...... ....base f3000000, size   8MB
PEX1_MEM0.... ....base cc000000, size  64MB
PEX2_IO...... ....no such
PEX2_MEM0.... ....no such
PEX3_IO...... ....base f5000000, size   8MB
PEX3_MEM0.... ....base d4000000, size  64MB
PEX4_IO...... ....base f6000000, size   8MB
PEX4_MEM0.... ....base d8000000, size  64MB
PEX5_IO...... ....no such
PEX5_MEM0.... ....no such
PEX6_IO...... ....no such
PEX6_MEM0.... ....no such
PEX7_IO...... ....no such
PEX7_MEM0.... ....no such
CRYPT_ENG..... ....base f7000000, size   2MB
INTER_REGS... ....base f1000000, size   1MB

  Marvell Development Board (LSP Version 2.0.2_Patch1_MV78XX0)-- DB-MV78200-A-BP  Soc: MV78200 LE

Detected Tclk 200000000 and SysClk 400000000
pci_preinit(): PCI-E 0 not mapped to this CPU.
pci_preinit(): PCI-E 1 not mapped to this CPU.
pci_preinit(): PCI-E 2 not mapped to this CPU.
pci_preinit(): PCI-E 3 not mapped to this CPU.
pci_preinit(): PCI-E 4 not mapped to this CPU.
pci_preinit(): PCI-E 5 not mapped to this CPU.
pci_preinit(): PCI-E 6 not mapped to this CPU.
pci_preinit(): PCI-E 7 not mapped to this CPU.
mv_pci_setup(): PCI-E 0 not mapped to this CPU.
mv_pci_setup(): PCI-E 1 not mapped to this CPU.
mv_pci_setup(): PCI-E 2 not mapped to this CPU.
mv_pci_setup(): PCI-E 3 not mapped to this CPU.
mv_pci_setup(): PCI-E 4 not mapped to this CPU.
mv_pci_setup(): PCI-E 5 not mapped to this CPU.
mv_pci_setup(): PCI-E 6 not mapped to this CPU.
mv_pci_setup(): PCI-E 7 not mapped to this CPU.
SCSI subsystem initialized
NET: Registered protocol family 2
Time: orion_clocksource clocksource has been installed.
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
RTC registered.
SHARED_MEM: INIT: Shared Memory mapped into Kernel space at Addr: 0x0 for size 0xc000000
SHARED_MEM: INIT: Shared Memory Header in Kernel space at Addr: 0xa0800000
shared_mem_module_init: Location of shm_dev: 93c14000
Use the XOR engines (acceleration) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
  o copy user to/from kernel buffers
Number of XOR engines to use: 1
Use IDMA channels for enhancing the following function:
Enable iDMA idma_chan0 interrupt IRQ 4 for iDMA 0
Enable iDMA idma_chan1 interrupt IRQ 5 for iDMA 1
Enable iDMA idma_chan2 interrupt IRQ 6 for iDMA 2
Enable iDMA idma_chan3 interrupt IRQ 7 for iDMA 3
mv_dma_init: iDMA channel 1 settings, state 0x00000000, cause 0x00000000 [0x00000000], mask 0x000004f0 [0x00000000], idmaCause 0x00000000, idmaMask 0x00000018
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 13) is a 16550A
Load Marvell Ethernet Driver
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload enabled
  o Receive checksum offload enabled
  o Transmit checksum offload enabled
  o Driver statistics enabled
  o Proc tool API enabled
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface:
Giga 0 is not mapped to this CPU
eth0 Giga 2 is not mapped to this CPU
Giga 3 is not mapped to this CPU

wait_for_init_shared_mem: Entering Mutex for shared memory init
SHARED_MEM: CPU1: READY TO WAIT FOR INITIALIZATION OF SHARED MEMORY
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
cfi_flash_0: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
cfi_flash_0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
3 cmdlinepart partitions found on MTD device cfi_flash_0
Creating 3 MTD partitions on "cfi_flash_0":
0x01dc0000-0x020c0000 : "kernel"
0x020c0000-0x035c0000 : "root_fs"
0x03b00000-0x03d00000 : "var"
mice: PS/2 mouse device common for all mice
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
eth0: started
IP-Config: Guessing netmask 255.255.0.0
IP-Config: Complete:
      device=eth0, addr=169.254.1.0, mask=255.255.0.0, gw=255.255.255.255,
     host=DB78xx0, domain=, nis-domain=(none),
     bootserver=169.254.123.234, rootserver=169.254.123.234, rootpath=
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 108K
Warning: unable to open an initial console.
Kernel panic - not syncing: No init found.  Try passing init= option to kernel.
shared_mem_panic_event: Kernel panic event handler called. Notifying VxWorks Core of Kernel panic.
Find all posts by this user
Quote this message in a reply
11-07-2015, 08:08 AM
Post: #3
RE: Kernel panic - not syncing: No init found.
I have a virtually identical problem on a Drobopro-FS... Is there anything that can be done? Hardware seems fine, so i assume all that's needed is for some way to write a good image back to the /dev/mtdblock1 flash
Find all posts by this user
Quote this message in a reply
01-10-2017, 02:49 AM
Post: #4
RE: Kernel panic - not syncing: No init found.
I'm having similar problem, but with Drobo 5N.

It looks like corrupted storage card.

See this tread: http://www.drobospace.com/forums/showthr...http://www.drobospace.com/forums/showthread.php?tid=146396&highlight=No+

I will keep you updated with progress.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump: